Cable set 1ch MP-EXT

Note: The NCx100EXT is available for pre-order. Please contact sales@hypex.nl for more information. The NCx100EXT is an NCOREx® based Class D amplifier add on module for the NC-MP and NCx-MP series. It is intended for use in active loudspeaker systems as an additional amplifier channel, optimised for mid and high frequency reproduction while supporting full audio bandwidth operation. The module is powered directly from the host NC-MP or NCx-MP module via the Hypex Channel Extension interface. It supports the available supply voltage range provided by the host module and does not require an external power supply. The NCx100EXT incorporates a self contained NCOREx® Class D amplifier. The design provides a flat frequency response independent of load impedance and maintains consistent distortion behaviour across the operating range. Radiated and conducted electromagnetic interference is controlled through circuit topology and PCB layout. Control is based on the NCOREx® self oscillating control architecture with feedback taken directly at the loudspeaker output. This topology supports stable operation and predictable electrical behaviour when integrated into multi channel active loudspeaker systems. The NCx100EXT is designed to expand NC-MP and NCx-MP based designs with an additional amplifier channel, supporting two way, three way or four way active loudspeaker configurations where an additional midrange or high frequency channel is required. Highlights • High efficiency • Flat, fully load-independent frequency response • Low output impedance • Very low, frequency independent THD • Very low noise Features • NCOREx® Technology • NCx-MP Add-on • External controlled operation • Specifically designed as channel extension for our Mains Powered NCORE® and NCOREx® modules Protections • Advanced overcurrent protection • Exessive DC protection • Short circuit protection • Over temperature protection Possible applications • Monitor loudspeakers for recording and mastering studios • Public address systems • Active loudspeakers ABOUT NCOREx® NCOREx® builds on the proven NCORE® architecture with a redesigned loop filter that increases loop gain across the audio band. This results in over 60 dB of error correction, further reducing distortion, improving linearity, and lowering output impedance for even more precise and controlled sound reproduction.

The NC100HF is a dedicated high frequency amplifier module designed for use with the Mains Powered NCORE® module family. It is intended to add an additional amplifier channel for high and mid frequency reproduction in active loudspeaker systems. The module is optimised for operation in the mid and high frequency range, starting at approximately 500 Hz. Its design supports controlled amplification of tweeter and midrange drivers in multi way active loudspeaker configurations. The NC100HF interfaces directly with the on board switch mode power supply of the Mains Powered NCORE® modules. This allows the module to be powered and controlled as part of an integrated NCORE®-based system without the need for an additional external power supply The NC100HF is suitable for use in two way and three way active loudspeaker designs where an additional high frequency amplifier channel is required. Its integration approach supports straightforward system expansion within the Mains Powered NCORE® platform. HIGHLIGHTS • High efficiency • Flat, fully load-independent frequency response • Low output impedance • Very low, frequency independent THD • Very low noise FEATURES • Advanced protections • External controlled operation • Light weight and compact size PROTECTIONS • DC protection • Short circuit protection POSSIBLE APPLICATIONS • Monitor loudspeakers for studios • Active loudspeakers and subwoofers • Public Address systems • Home Theatre systems • Power Amplifiers; for home and professional use

The DSP3-213 is a mono DSP module based on the Analog Devices ADAU1452. It is intended for use with mains powered NCORE® amplifier power modules and Fusion amplifier platforms. The module supports mono and 3-way active loudspeaker configurations. Signal processing is configured using Hypex Filter Design software and supports both IIR and FIR filters. Multiple presets can be stored for different filter sets, input selections and gain settings. The DSP3-213 supports features such as auto signal detect and configurable standby behaviour. The module can be expanded with optional input boards, such as digital input or subwoofer input modules. Multiple DSP3-213 units can be configured in a master-slave setup for stereo or 2.1 systems. Typical applications include active loudspeakers, studio monitors and integrated amplifier systems where a compact mono DSP solution is required. Highlights • Three channel active filtering • One FIR (4500 taps) or three (1500 taps per channel) per preset • Compatible with NCMP and NCAS series • Three programmable presets Features • Configurable Soft clip limiter • IIR & FIR capable • Programmable with Hypex Filter Design (HFD) • Automatic source selection • Automatic signal detection • Optional IR remote control Possible applications • High-end consumer audio • Active loudspeakers • Subwoofers • PA systems • Studio monitors