Filter
Stainless Steel Blue Illuminated Push Button
Stainless steel push button with blue LED illumination. Ideal for controlling the softstart module. APPLICATIONS:PreamplifiersAmplifiersSoftstart control GENERAL FEATURES:Stainless steelFront panel mountingRing illuminationSingle pole push to makeScrew terminalsSeparate LED terminals (outer terminals ‘+’ and ‘-‘) MPI002/TERM/BL ELECTRICAL FEATURES:Switch rating (max): 50mA @ 24VdcLED rating (Max): 20mA @ 3.5V

Neutrik XLR male 3 pole cable connector
3 pole male XLR cable connector from Neutrik with black metal housing and gold plated contacts.

Mounting set red faston 10pcs
This set of 10 pieces isolated red fastons can be used for several purposes like connecting your transformer or power supply to your power connector. To mount these on your cable you can use our Faston crimping tool. These Fastons are for cables between 0.5-1.5mm. Fits the UcD series.

Neutrik XLR female 3 pole cable connector
3 pole female XLR cable connector from Neutrik with black metal housing and gold plated contacts.

SMPS1200 to NC500 / 1200 / 2k cable
Cable suited for SMPS1200 to NC500 converter or directly to NC1200 and NC2k. Specifications:Length: 230mmCable: 4x 14AWGConnector: 2x JST VLP-06VContact pin: 12x SVF-81T JSTCable asm name: Z6A23L1

Power cable black Euro-IEC 60320 C13
Mains power cable to connect your products with IEC 60320 C13 and Euro connection.

Cable set SMPS3k
The cable set SMPS3k is a complete set of cables to connect the SMPS3k to one amplifier module. If you want to connect 2 or 3 amplifiers you'll need 2 or 3 cable sets. Cable length: 30cm

Cable set NC1200 / NC2k
The Cable set NC1200 / NC2k is a cable set to connect the NC1200 or NC2k amplifier to our SMPS1200 or SMPS3k power supplies.All needed cables are included.

Cable set UcD700LZ
Cable set suitable for the UcD700LZ amplifier module.

Neutrik XLR male 3 pole cable chassis
3 pole male XLR cable chassis plug from Neutrik with black metal housing and gold plated contacts.

Cable set SMPS1200
The cable set SMPS1200 is a complete set of cables to connect the SMPS1200A180, SMPS1200A400 or the SMPS1200A700

Neutrik XLR female 3 pole cable chassis
3 pole female XLR cable chassis socket from Neutrik with black metal housing and gold plated contacts/soldercups. Neutrik part: NC3FDLB1

Ncore signal cable
50cm balanced signal cable with 4-pin connector also providing the enable signal.SpecificationsThe QuietConduit cable design incorporates several refinements over normal balanced cables. A conductive polymer interface layer between the braid shield and the insulation of the signal conductor short-circuits triboelectric currents where they are generating, virtually eliminating microphonic noise pickup.A secondary benefit of this layer is to improve the electrostatic shielding effectiveness of the braid shield. Another crucial improvement is the elimination of drain wires, which is normally included for ease of termination but which allow shield currents to couple noise asymmetrically into the signal conductors. The geometry of the QuietConduit cable is precisely controlled, insuring that any noise coupling is strictly limited to common mode.

Mounting set blue faston 10pcs
This set of 10 pieces isolated blue fastons can be used for several purposes like connecting your transformer or power supply to your power connector. To mount these on your cable you can use our Faston crimping tool. These Fastons are for cables between 1.5-2.5mm. Fits the UcD series.

Neutrik Speakon NL4MP cable chassis
Neutrik Speakon NL4MP to connect your amplifier or other device to your speakers.

USB Cable
With this USB cable you can connect the FusionAmp series plate amplifier to your PC.Specifications:USB A - Mini-USB BLength: 1.8 m

Cable set NCxxxMP
The Cable set NCxxxMP is a complete cable set to connect the NCxxxMP amplifier to your application. Note: For the connection of the NC100HF please refer to the "Cable set NC100HF". NCore signal cable not included and not needed with the NCxxxMP amplifier range.

UcD signal cable
50cm balanced signal cable with 4-pin connector also providing the enable signal. Specifications The QuietConduit cable design incorporates several refinements over normal balanced cables. A conductive polymer interface layer between the braid shield and the insulation of the signal conductor short-circuits triboelectric currents where they are generating, virtually eliminating microphonic noise pickup. A secondary benefit of this layer is to improve the electrostatic shielding effectiveness of the braid shield. Another crucial improvement is the elimination of drain wires, which is normally included for ease of termination but which allow shield currents to couple noise asymmetrically into the signal conductors. The geometry of the QuietConduit cable is precisely controlled, insuring that any noise coupling is strictly limited to common mode.

Cable set loudspeaker FA 3 way
The cable set loudspeaker FA 3 way is a complete cable set to connect your 2 or 3 way Fusion Amp with your loudspeaker. This is the same loudspeaker cable set as supplied with new Fusion Amps. The length of the cables is 125cm.

Power Cable Black US-IEC 60320 C13
Mains power cable to connect your products with USA and IEC 60320 C13 connection.

Fusion OLED Display
All models of the Fusion Amplifier Family and the DSP3-213 can be extended with the Fusion OLED Display. The Fusion OLED Display will show you all the relevant information such as volume level, active input and preset and will show you all error messages. All messages are very well readable from your listening position. You can mount this Display from the outside of the speaker cabinet. the Display is already fitted with double adhesive tape for assembly in your speaker cabinet. This Display must be used in master devices if the Hypex remote is to be used (remote not included). Furthermore, this Display can also be added in slave devices, but the IR functionality will be disabled. includes: Fusion OLED Display 5 pin cable 125cm Manual

  • Compatible with: DSP3-213
  • Compatible with: Fusion Amplifier Family
Switch on-off
This on-off switch can be used as a main switch for your amplifier cabinet. This snap-in switch can handle 16A at 230V. The mounting hole is 31 x 11mm and ~ 25mm deep including the faston terminals.

Cable set NC100HF
The Cable set NC100HF is a complete cable set to connect the NC100HF hanger module to your NCxxxMP amplifier module or with the MP-DSP Main.Note: For the connection of the NCxxxMP amplifier module please refer to the "Cable set NCxxxMP".NCore signal cable not included and not needed with the NCxxxMP amplifier range.

Cable set SMPS400
The cable set SMPS400 is a complete set of cables to connect the SMPS400A180 or the SMPS400A400.

Cable set loudspeaker FA 1 way
The cable set loudspeaker FA 1 way is a complete cable set to connect your 1 way Fusion Amp with your loudspeaker. This is the same loudspeaker cable set as supplied with new Fusion Amps.The length of the cable is 125cm.